SS Flanges
Steelage Overseas established international reputation as one of the leading stockiest and supplier of quality stainless steel flanges. We have varying size available in SS Flanges but we are also happy to discuss your custom requirements. We have high quality stainless steel flanges in different material grades to meet industry specific applications.

SS Flanges

We offer variety of stainless steel flanges that are extensively used in many industrial applications. Our products are well known because of its durability and strength. Our products are work better in various applications and compare to other flanges our SS flanges work longer. We have different specifications and grades of SS flanges.

Below we have mentioned different Stainless steel flanges that we trade:


Weld Neck Flanges

WELDING NECK FLANGES are distinguished from other types by their long tapered hub and gentle transition of thickness in the region of the butt weld joining them to the pipe. The long tapered hub provides an important reinforcement of the flange proper from the standpoint of strength and resistance to dishing. The smooth transition from flange thickness to pipe wall thickness effected by the taper is extremely beneficial under conditions of repeated bending, caused by line expansion or other variable forces and produces an endurance strength of welding neck flanged
assemblies equivalent to that of a butt welded joint between pipes, which, in practice, is the same as that of unwelded pipe. Thus this type of flange is preferred for every severe service condition, whether this results from high pressure or from sub-zero or elevated temperature, and whether loading conditions are substantially constant or fluctuate between wide limits.

Slip-On Flanges

SLIP-ON FLANGES continue to be preferred to welding neck flanges by many users on account of their initially lower cost, the reduced accuracy required in cutting the pipe to length, and the somewhat greater ease of alignment of the assembly; however their final installed cost is probably not much, if any, less than that of welding neck flanges. Their calculated strength under internal pressure is approximately two-thirds that of welding neck flanges, and their life under fatigue is about one-third that of the latter. For these reasons, slip-on flanges are limited to sizes ½" to 2 ½" in the 1500 lb standard and are not shown in the 2500lb standard.

Blind Flanges

BLIND FLANGES are used to blank off the ends of piping, valves and pressure vessel opening. From the standpoint of internal pressure and bolt loading, blind flanges, particularly in the larger sizes, are the most highly stressed of all flange types; however, since the maximum stresses in a blind flange are bending stresses at the center, they can safely be permitted to be higher than in other types of flanges.

Lap - Joint Flanges

LAP JOINT FLANGES are primarily employed with lap joint stubs, the combined initial cost of the two items being approximately one-third higher than that of comparable welding neck flanges. Their pressure-holding ability is little, if any, better than that of slip-on flanges and the fatigue life of the assembly is only one-tenth that of welding neck flanges. The chief use of lap joint flanges in carbon or low alloy steel piping systems is in services necessitating frequent dismantling for inspection and cleaning and where the ability to swivel flanges and to align bolt holes materially
simplifies the erection of large diameter or unusually stiff piping. Their use at points where severe bending stress occurs should be avoided.

Threaded Flanges

THREADED FLANGES are confined to special applications. Their chief merit lies in the fact that they can be assembled without welding this explains their use in extremely high pressure services, particularly at or near atmospheric temperature, where alloy steel is essential for strength and where the necessary post weld heat treatment is impractical. Threaded flanges are unsuited for conditions involving temperature or bending stresses of any magnitude, particularly under cyclic conditions, where leakage through the threads may occur in relatively few cycles of heating or stress; sea welding is sometimes employed to overcome this, but cannot be considered as entirely satisfactory.

Socket Weld Flanges

SOCKET WELDING FLANGES were initially developed for use on small size high pressure piping. When provided with an internal weld, their static strength is equal to, but their fatigue strength 50% greater than double welding slip-on flanges. Smooth bore conditions can readily be attained (by grinding the internal weld) without having to bevel the flange face and, after welding, to reface the flange as would be required with slip-on flanges. The internally welded socket type flange is popular in chemical process piping for this reason.

Orifice Flanges

ORIFICE FLANGES are widely used in conjunction with orifice meters for measuring the rate of flow of liquids and gases. They are basically the same as standard welding neck and slip-on flanges except for the provision of radial, tapped holes in the flange ring for meter connections and additional bolts to act as jack screws to facilitate separating the flanges for inspection or replacement of the orifice plate. In choosing the type of orifice flange, the considerations affecting the choice of welding neck and slip-on standard flanges apply with equal force.
Stainless Steel ASTM A 182, A 240
Grade F 304, 304L, 304H, 316, 316L, 316Ti, 310, 310S, 321, 321H, 317, 347, 347H
Carbon Steel ASTM A 105, ASTM A 181
Alloy Steel ASTM A 182, GR F1, F11, F22, F5, F9, F91
Nickel Alloys Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy 904
Duplex Steel Grade: 2205 (UNS No. S31803), 2207 (UNS No. S32760)
Nickel Alloy
Grade
  • Nickel 200
    (UNS No. N02200)
  • Nickel 201
    (UNS No. N02201)
  • Inconel 800
    (UNS No. N08800)
  • Inconel 825
    (UNS No. N08825)
  • Inconel 600
    (UNS No. N06600)
  • Inconel 625
    (UNS No. N06625)
  • Inconel 601
    (UNS No. N06601)
  • Hastelloy C 276
    (UNS No. N10276)
  • Alloy 20
    (UNS No. N08020)
  • Titanium (Grade I & II)
Copper Alloy
Grade UNS No. C 10100, 10200, 10300, 10800, 12000, 12200, 70600, 71500,
UNS No. C 70600 (Cu -Ni- 90/10), C 71500 (Cu -Ni- 70/30)
Types Weldneck, Slipon, Blind, Socket Weld, Lap Joint, Spectacles, Ringjoint, Orifcase, Long Weldneck, Deck Flange, etc.
Size 1/8" NB TO 48"NB
Class 150#, 300#, 400#, 600#, 900#, 1500# & 2500#